Can you embroider a waterproof hi vis jacket?
Yes. But here is why we print them, and when embroidery still makes sense.
From now until March your crew lives in a waterproof jacket. That is also when we get asked the same question most weeks: can you stitch our logo onto these?
The short answer is yes. We embroider and print every day on the Dock Road, and we can put either finish on a hi vis jacket. But on a fully waterproof jacket we nearly always recommend print, because stitching pushes thousands of needle holes through the layer that keeps the rain out.
Here is the reasoning, so you can make the call for your own crew.
A raised, premium finish. Best on hi vis softshells, fleeces and bodywarmers that are not fully waterproof.
Sits on the surface of the fabric, so the waterproof membrane stays sealed and your crew stays dry.
What actually keeps a hi vis jacket waterproof
A waterproof hi vis jacket is not waterproof because of the fabric alone. It relies on three things working together.
- A coated or laminated outer. Budget site jackets like the ST Standard Bomber use a 300D Oxford polyester with a PU coating on the inside. Step up jackets like the SIR Safety Matrix or the Helly Hansen Alna 2.0 bond a membrane to the outer fabric.
- Taped seams. Every seam the factory sews leaks through its needle holes, so the manufacturer seals each one with tape on the inside. That one detail tells you how seriously they take a needle hole.
- An EN 343 rating. This is the European standard for protection against rain. The first number on the label is water penetration resistance, the second is breathability. The rating was earned by the jacket as it left the factory, with nothing stitched through it.
Take any one of those away and the jacket is no longer the jacket you paid for.
What embroidery does to the membrane
Embroidery works by stitching thread through the fabric. A standard left chest logo runs to several thousand stitches, and every stitch is a needle hole through the outer, the coating or membrane, and often the lining behind it.
In practice that means:
- Water finds its way in. On a long wet day, rain works through the stitched area and the thread itself can draw moisture inwards. Your crew feels it as a damp patch on the chest or shoulder.
- The EN 343 rating no longer describes the jacket. It was tested unbroken, and an embroidered patch of holes is not what was tested.
- The warranty may not cover it. Some manufacturers treat stitching through a waterproof shell as damage.
None of this matters on a fleece or a polo. It matters a lot on a jacket whose whole job is to keep someone dry for a ten hour shift in November.
Why print keeps the jacket sealed
We brand waterproof jackets with digital print. Your logo is printed in full colour and pressed onto the surface of the jacket, so it bonds to the outer fabric without a single needle going through it. The coating, the membrane and the taped seams are left exactly as the manufacturer made them.
Print also suits site jackets for reasons beyond the weather:
- Big and readable. A company name across the back reads from the far side of a site. A back sized embroidery is heavy, stiff and expensive, so print is the natural choice there anyway.
- Full colour, fine detail. Gradients, small text and multi colour logos come out clean.
- Matched to the fabric. We set the press for each jacket, because a PU coated bomber and a membrane shell need different settings.
- Kept compliant. We place the print on the fluorescent fabric, clear of the reflective tape, and size it so the jacket keeps its EN ISO 20471 class. Our guide to Class 1, 2 or 3 explains why that matters.
When embroidery still makes sense
Print is our recommendation, not a rule. There are good reasons to choose embroidery on hi vis, and we do it every week.
You want the stitched look on the jacket itself
We will embroider it. We keep the logo small with a low stitch count, place it high on the left chest, and talk you through the trade off first. On jackets with a decoration access zip, like the Portwest T400 PW3, we can reach the outer shell without stitching through the lining. That keeps the inside neat, but the outer still takes the needle holes.
The hi vis garment is not fully waterproof
Hi vis softshells, fleeces, polos and sweatshirts do not rely on an unbroken membrane, so embroidery is often the better finish. The SIR Safety Shark softshell is a good example, and the full range is in hi vis fleece and softshell.
You layer the two
This is what most of our customers end up doing. Your crew stays dry on site and still looks the part in the site office or across the table from a client.
Company name across the back, logo on the chest. Keeps the rain out.
Stitched left chest logo. The smart layer for indoors and client meetings.
See how we stitch on our embroidery page.
A quick guide by garment
If the garment keeps the rain out with a membrane or coating, print it. If it does not, embroidery is on the table.
| Hi vis garment | Fully waterproof? | We recommend |
|---|---|---|
| Bomber or parka with a PU coated outer | Yes | |
| Rain jacket or shell with taped seams | Yes | |
| Bodywarmer | Depends on the shell | Print if waterproof, embroidery if not |
| Softshell | Water resistant only | Either |
| Fleece | No | Embroidery |
| Polo or sweatshirt | No | Either |
Waterproof hi vis jackets we print most
- SupertouchST Standard BomberClass 3 with a PU coated outer, the volume pick for whole crews
- SIR SafetyMatrix hi vis jacketTPU membrane and heavy padding, the best value step up
- SIR SafetyAndromeda jacketFully waterproof with taped seams and a detachable padded inner, so it works across three seasons
- PortwestT400 PW3 winter jacketTaped seams and EN 342 cold protection
- PortwestDX430 DX4 winter jacketWaterproof PU membrane and taped seams, with stretch panels for crews who climb, kneel and reach
- Helly HansenAlna 2.0 shellFor all day work in the worst weather
For the full comparison with prices, read our winter work jackets guide, or browse all hi vis jackets. For office teams, our guide to printed or embroidered jackets covers softshells and corporate wear.
Frequently asked questions
Will embroidery make my hi vis jacket leak?
It can. Every stitch is a hole through the waterproof layer, and unlike the seams, the back of a logo is not taped. On a fully waterproof jacket we recommend print for that reason.
Does printing affect the hi vis certification?
Not when it is done properly. We keep the print on the fluorescent fabric, clear of the reflective tape, and sized so the jacket stays in its EN ISO 20471 class.
Can I have embroidered and printed garments on one order?
Yes. Printed waterproof jackets for the crew and embroidered softshells or polos for supervisors and the office all go on one order and one invoice.
Can you add names to a waterproof jacket?
Yes. Digital print handles individual names and job titles, so each jacket can carry its own name under the company logo.
Is there a minimum order?
There is no minimum order on jackets. Send us the quantity and we will price it.
Branding waterproof jackets this winter?
We have been printing and embroidering workwear in Limerick since 1994. Send us your headcount, the jacket and your logo, and we will come back with pricing and a free digital proof. Orders are dispatched within 5 to 8 working days of artwork approval.






